News:

The Forum is back!

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - jpezdek

#1
General/Off-Topic / FS or free
March 28, 2019, 02:52:02 PM
Parts for ariel
let me know what you need and i may have it for free except for shipping

Parts for sale are
rudder shoe
forestay bracket
text 516 972 4324
joe
#2
General/Off-Topic / FS Ariel Parts
June 16, 2018, 08:33:09 AM
FS
Stem head fitting with bolts
boom with fittings
mainsail
tiller fitting

SS chain plates new
rudder shoe new
miscellaneous parts

text at 516 972 4324 leave message
thanks
#3
General/Off-Topic / FS Ariel 214
February 15, 2017, 05:12:45 PM
FS Ariel 214 $1200
probable made in 1964
includes 8hp yamaha 2 stroke long shaft motor, anchor, main and two jibs portapotti, etc
located in Bayshore, NY by NYC
general condition good, non skid needs repainting
stored on land in winter and in a slip during summer
call 516-972-4324 leave a message
#4
General/Off-Topic / FS Ariel 214
September 11, 2016, 04:29:39 PM
FS Ariel 214
On land for the winter will be in water in the spring
main and two jibs
NY registration
located on Long Island, NY next to NYC
$1400 negotiable
8hp Yamaha long shaft 2 stroke, anchor, lifejackets,etc
additional pictures available
sail away condition

call 516 972 4324 leave msg
email at jpezdek at yahoo.com
#5
General/Off-Topic / genoa
August 29, 2016, 11:26:13 AM
I have a hank on genoa used maybe 2 or 3 times. It is from a 25 catalina, but should fit. I am in Long Island NY.
Please call 516 972 4324 and leave a message.
#6
General/Off-Topic / FS Catalina 25 genoa jib
November 22, 2015, 01:21:47 PM
$500 plus shipping

150 genoa jib
From Catalina 25
Hank on (plastic not brass hanks)
D and D Sailmakers Inc
I think the size is Luff 28.5
Leech 28
Foot 16
Used about 3 times
No sailbag

Prefer a local buyer so they can see the sail (I am in Long Island NY)
If interested call 516 972 4324
#7
Technical / Cabin Table
September 13, 2013, 12:08:26 PM
The above picture is the same table I have for my Ariel 214. It is large, heavy and was from the factory. It is wider and shorter than the door. I also have the original door.
I am having trouble logging into the site. I log in then get a message that you're not logged in and asked to log in again and again. It seems like I am in a loop.
#8
Technical / ariel table and mast climber
September 11, 2013, 12:50:50 PM
I have an ariel table in good condition and might be interested in your mast ladder.
Joe
jfpezdek at yahoo dot com
#9
Technical / outboard moto well
March 22, 2007, 01:41:10 PM
The dimensions of my outboard motor well are approximately

12 1/2 to 13 inches wide at the top (inside dimension)
12 to 12 1/2 inches from front to back(inside dimension)
front side is approximately 11 inches deep
back side is approximately 6 inches deep

the front and back sides are slanted and roughly parallel the line of the transom

Ariel 214